.
Home Technical Details Suppliers Contacts About Us

Burgener Nebulizers:

 While our 2016-2021 prices were the same as in 2005 and lower than in 2014, inflation has increased the costs of our supplies and we needed to raise our prices in 2022. The overall increase is approximately 10% relative to our previous 10 years of prices. As usual, especially with the present currency variations and strange economic times, we reserve the right to change prices at any time. Non US prices are based on the exchange rate of the day. Shipping and Taxes are extra.

NOTE: we accept both VISA and MC, but we have Canadian accounts, and we must convert the prices to Canadian equivalents when processing VISA and MC. Such conversions will be at the present exchange rates. We try to calculate it so that the converted US$/Euro/GBP price will be equal to or lower than the US list prices.

. 		All Burgener Nebulizers are made with the patented Enhanced Parallel Path Method.
US Patent # 6,634,572; Canadian Patent # 2,384,201



For approximate prices in £ and €, Click Here
Top  Nebulizers Gas Lines
& Fittings 		Sample Lines
& Fittings 		Discontinued
Nebulizers etc.

Nebulizers

Nebulizers for ICP and ICP/MS

Teflon Mira Mist
Can operate on 0.2 ml/min to 2.5 ml/min. Excellent mist, and can handle high level of particulates in sample. Fits regular chambers as a direct replacement for glass concentric nebulizers. Operates on standard pressures of 35 - 45 psi. The Teflon Mira Mist can be used for any liquid. Salting is very rare, but can occur over long periods of time, especially with high Sodium levels in the solution. Such salting can be cleared easily with a dip in 5 - 10% HF, (Caution: Be careful when handling HF. It soaks into the skin before you feel it burning, and in low concentrations it looks like water.)

Description ID (Microns) Catalog # US$ Price
Teflon Mira Mist 500 TMM 3500 $ 1095.00

Teflon Mira Mist II
Same as the Teflon Mira Mist, but with a 1/4-28 thread at the back for the sample line. Made to simplify connections to flow injection and similar attachments. Uses Idex chromatographic fittings, and 1/16” (1.5mm) sample lines. Can operate on 0.2 ml/min to 2.5 ml/min. Excellent mist, and can handle high level of particulates in sample. Fits regular chambers as a direct replacement for glass concentric nebulizers. Operates on standard pressures of 35 - 45 psi. The Teflon Mira Mist can be used for any liquid. Salting is very rare, but can occur over long periods of time, especially with high Sodium levels in the solution. Such salting can be cleared easily with a dip in 5 - 10% HF, (Caution: Be careful when handling HF. It soaks into the skin before you feel it burning, and in low concentrations it looks like water.)

Description ID (Microns) Catalog # US$ Price
Peek Mira Mist 500 TMM-2 $ 1095.00

PEEK Mira Mist
Same as the Teflon Mira Mist, but easier to make than the Teflon Mira Mist, so you save a little. Works for most samples, but not concentrated acids, and not some organic solvents. Still has Teflon capillaries for the samples and for the gas. Standard pressure (45 psi), low sample flow, enhanced parallel path design. Can operate on 0.2 ml/min to 2.5 ml/min. Excellent mist, and can handle high level of particulates in sample. Fits regular chambers as a direct replacement for glass concentric nebulizers.

Description ID (Microns) Catalog # US$ Price
Peek Mira Mist 500 PMM 4000 $ 995.00

PEEK Mira Mist II
Same as the PEEK Mira Mist, but with a 1/4-28 thread at the back for the sample line. Made to simplify connections to flow injection and similar attachments. Uses Idex chromatographic fittings, and 1/16” (1.5mm) sample lines. Works for most samples, but not concentrated acids, and not some organic solvents. Has PFA Teflon capillaries for the samples and for the gas. Standard pressure (45 psi), low sample flow, enhanced parallel path design. Can operate on 0.1 ml/min to 2.5 ml/min. Excellent mist, and can handle high level of particulates in sample. Fits regular chambers as a direct replacement for glass concentric nebulizers.

Description ID (Microns) Catalog # US$ Price
Peek Mira Mist II 500 PMM-2 $ 995.00

T 2100
Huge Sample Capillary: 750 microns / 1/32 inch. Designed as replacement for T2002 and BTN. Essentially unpluggable with un-dissolved particles. Can operate on 0.5 ml/min to 3.0 ml/min. Excellent mist, but not quite as good as Mira Mist, but better than most concentrics. Can handle very high level of particles in sample. Fits regular chambers as a direct replacement for glass concentric nebulizers. Operates on standard pressures of 30 - 45 psi.
The T 2100 can be used for any liquid. Salting is very rare, but can occur over long periods of time, especially with high Sodium levels in the solution. Such salting can be cleared easily with a dip in 5 - 10% HF, (Caution: Be careful when handling HF. It soaks into the skin before you feel it burning, and in low concentrations it looks and feels like water.)

Description ID (Microns) Catalog # US$ Price
T 2100 750 T 2100 $ 995.00

PFA 250 & PFA 260
Low Flow design for ICP/MS. PFA nose and inner capillaries and all wetted parts. Peek body for strength and longevity. Sample Capillary: 250 microns. Designed for ICP/MS where low flow is desired and PFA only touching the liquids is desired. Operates from 50 ΅l/min to 2 ml/min. Excellent mist, seems to be more stable, and have lower %RSD than a Mira Mist.
The PFA 250 is set to run higher gas flows for the PE NexION which typically runs at 1.2 L/min. It uses 45 psi for 1 L/min.
The PFA 260 is set to run at higher pressure than a Mira Mist, but well within most instruments standard ranges. It uses about 40 psi for .65 L/min or 60 psi for 1 L/min.
The PFA 250 and PFA 260 can be used for any liquid.

Description L/min at 50 psi ID (Microns) Catalog # US$ Price
PFA 250 1.1 L/min 250 PFA 250 $1200.00
PFA 260 0.8 L/min 250 PFA 260 $1200.00

Ari Mist

Very low sample flow, enhanced parallel path design. Standard pressure (40 - 50 psi). Black PEEK body, Teflon sample and gas capillaries. Can operate on 0.050 ml/min to 1.0 ml/min. Good for ICP and ICP/MS. Only for samples that are particulate free. Fits regular chambers as a direct replacement for glass concentric nebulizers.

Description ID (Microns) Catalog # US$ Price
Ari Mist 225 AM 5000 $ 1100.00

X–175 and NX-175
Low Flow design for ICP/MS. Peek inner capillaries, PTFE nose, Peek Body for strength and longevity. Sample Capillary: 175 microns. Operates from 50 ΅l/min to 1 ml/min. Excellent mist, is more stable and has lower %RSD than an Ari Mist.
The X-175 is set to run at a bit higher pressure than a Mira Mist, but well within most instruments standard ranges. Uses about 40 psi for .65 L/min
The NX – 175 is set to run higher flows as required for the PE NexION and Varian / Brooker ICP/MS with 1.2 L/min at 50 psi.
Note: This nebulizer’s sample flow rates are much lower than normal for ICP OES.

Description L/min at 50 psi ID (Microns) Catalog # US$ Price
NX-175 1.2 L/min 175 X-175 $1200.00
X-175 0.8 L/min 175 NX-175 $1200.00

NEW! SC–175
Very Low Flow designed specifically for single cell analysis for ICP/MS. Peek inner capillaries, PTFE nose, Peek Body for strength and longevity. Sample Capillary: 175 microns. Operates from 5 ΅l/min to 1 ml/min.
The SC-175 is a variation of the X-175, but tuned for very low flow capability.
The SC-175 is set to run at a bit higher pressure than a Mira Mist, but well within most instruments standard ranges. Uses about 40 psi for .65 L/min
Note: This nebulizer’s sample flow rates are much lower than normal for ICP OES.

Description L/min at 50 psi ID (Microns) Catalog # US$ Price
SC-175 0.8 L/min 175 SC-175 $1450.00

ENYA Mist

Ultra low sample flow, enhanced parallel path design. Standard Pressure (50 psi). Our lowest flow ICP/MS nebulizer. Runs from 200 nanoliters/minute to 50 ΅l/min. Designed for ICP/MS - HPLC interface, tiny samples, and for Split flow applications - simple addition of a T connection allows 500 ΅l/min pumped to nebulizer, with 10 - 20 ΅l/min delivered to nebulizer. Produces very low oxides in ICP/MS. Can NOT handle high level of particulates in sample. Fits regular chambers as a direct replacement for glass concentric nebulizers. Straight chambers are better than cyclonics - sample drops are lost in cyclonics on the wall beside the injection point.

Description ID (Microns) Catalog # US$ Price
Enya Mist 60 EM 6000 $1300.00

Mira Mist CE

Designed for ICP/MS - CE interface. Medium pressure (80-90 psi), Very low sample flow (10 ΅l/min or less), enhanced parallel path design. Can operate on 0.01 ml/min to 2.5 ml/min. With Alcohol solutions can operate down to .001 ml/min. Excellent mist, can handle high level of particulates in sample. Fits regular chambers as a direct replacement for glass concentric nebulizers. Designed for CE / ICP / MS analysis. Allows CE capillary to extend to tip of nebulizer for zero suction, zero back pressure CE interfacing with ICP / MS. Works best with mini chamber.

Description ID (Microns) Catalog # US$ Price
Mira Mist CE 500 MM CE $3950.00


T2002

Our old original standard nebulizer. Works well on most instruments. Fits most chambers. Best results are with Cyclonic Chambers. The T2002 was scheduled to be discontinued in Jan, 2010. However, we have decided to continue to have it available as long as there is a demand for them, and the one person who can make them continues to do so. For most applications, the T2100 is a better nebulizer since it handles larger particles, lasts longer, and provides virtually the same intensities and stability. As of Jan, 2017, we are continuing to produce the T2002 to meet demand.

Description ID (Microns) Catalog # US$ Price
T2002 450 T2002 $1095.00



Industrial Nebulizers

LB 30

Teflon Low Pressure (35 - 45 psi), High sample flow, Enhanced Parallel Path design. Designed for Industrial Sprays. Virtually unpluggable. Can run saturated solutions without salting up.

Description ID (Microns) Catalog # US$ Price
LB 30 2000 LB 30 $850.00

LB 80 & LB 100

Teflon, High sample flow, High gas flow (50 - 100 L/min), Enhanced Parallel Path design. Designed for Industrial Sprays. Virtually unpluggable. Can run saturated solutions without salting. Still maintains small droplets with a median of 10 - 20 microns diameter. To differentiate the gas line and liquid line, we use a 4mm gas line and a 3 mm liquid line. The LB 80 and 100 are identical except that the LB 100 gas orifice is a bit larger ID than for the LB 80.

Description ID (Microns) Catalog # US$ Price
LB 80 3000 LB 80 $995.00
LB 100 3000 LB 100 $1095.00

SS 50

Stainless Steel Industrial Nebulizer for hot environments, any length possible, 1/8" OD.
Low Pressure (45 psi) to very high pressure (5,000 psi), Low sample flow to high sample flow (10 ΅l/min to 5 mL/min), Enhanced Parallel Path design. Designed for Industrial Sprays.

Description ID (Microns) Catalog # US$ Price
SS 50 2000 SS 50 $1095.00

.
For prices in £ and €, Click Here
Top  Nebulizers Gas Lines
& Fittings 		Sample Lines
& Fittings 		Discontinued
Nebulizers etc.

Gas Lines & Fittings

Mira Mist and Ari Mist Gas & Sample Line Fittings



Burgener Nebulizers such as our Mira Mist and Ari Mist nebulizers use 2 mm gas lines and UpChurch 10/32 finger tight fittings for the gas lines and for the sample lines. Although this allows for simple attachment of GC/LC/CE systems, it is not the standard for other nebulizers. To ensure simple attachments to your instruments gas output connections, we have an extensive array of fittings available.

Gas line fittings are usually included with the nebulizer. Please note that we try to send the correct fittings with the nebulizers, but there are many to select from, and we sometimes send the wrong one. Please use the following list to correctly identify your gas fittings and call us for a replacement.
Instrument Burg Res Part Number
. .
Agilent / HP Gas line: BRG 200
Sample Line: BRC 204, BRC 204A or BRC 2000
Agilent 4200 series ICP OES Gas line: BRG 306
Sample line: BRC 204 or BRC 204A
Agilent 5100, 5110 ICP OES Gas line: BRG 200
Sample line: BRC 204, BRC 204A or BRC 2000
Agilent 7700, 7800, 7900, 8800, 8900 … Series Gas line: BRG 204
Sample line: BRC 204, BRC 204A or BRC 2000
Agilent / Varian ICP Gas line: BRG 306
Sample Line: BRC 204, BRC 204A or BRC 2000
Analytic Jena BRG 204
Bruker ICP/MS BRG 306
Finnigan including the Finnigan Neptune BRG 306
GBC BRG 306
Hitachi High-Tech Science ICP BRG 106
JY BRG 204
Leeman BRG 306
Nu Plasma ICP-MS BRG 204
PE / Sciex Elan ICP/MS (1/4" Swagelok gas lines) BRG 206
PE NexION 300 & 350 ICP/MS BRG 206
PE NexION 2000 ICP/MS BRG 203
PE Optima 3000 series BRG 206
PE Optima 2000, 4000, 5000, 7000, & 8000 series BRG 308
PE Avio 200, 500 BRG 308
Shimadzu ICP/MS BRG 303
SII NanoTechnology ICP BRG 106
Spectro BRG 309
Thermo Scientific - TJA ICP (Luer Lock fitting) BRG 305
Thermo Scientific - iCAP 6000 series ICP BRG 204
Thermo Scientific - iCAP 7000 series ICP Gas Line: BRG 204
Sample Line for 7000: BRC 203
Sample Line for 7200: BRC 204
Sample Line for 7400: BRC 204
Thermo Scientific - ICP/MS X series BRG 204
Thermo Scientific - ICP/MS iCAP Q, iCAP TQ, iCAP RQ BRG 204
Thermo Scientific - Finnigan Neptune ICP/MS BRG 306
Thermo Scientific - VG Elemental ICP/MS pre 2002 BRG 307
Varian - ICP BRG 306
. .


10/32 to Swagelok
Description Catalog # US$ Price

BRG 103

1/8" Adapter for 1/8" gas lines. BRG 103 $40.00

BRG 104

4 mm Adapter for 4 mm gas lines. BRG 104 $40.00

BRG 106

1/4" Adapter for 1/4" gas lines. BRG 106 $40.00


10/32 to Straight Tube
Description Catalog # US$ Price

BRG 200

4 mm FEP Adapter for older Agilent ICP/MS
that use a barb fitting on the side of the instrument to attach the gas line. 		BRG 200 $ 50.00

BRG 203

1/8" Adapter. BRG 203 $40.00

BRG 204

4mm Adapter for JY, VG X-series, Thermo ICP/MS, iCap Series instruments.
and for newer Agilent ICP/MS that use a quick release on the instrument.		 BRG 204 $40.00

BRG 214

4 mm Adapter as supplied with JY nebulizers. Not for other instruments. BRG 214 $40.00

BRG 206

1/4" Adapter for PE Optima 3000 series, PE Sciex ICP/MS. BRG 206 $40.00


10/32 to Quick Release
Description Catalog # US$ Price

BRG 303

Quick Release for Shimadzu BRG 303 $ 50.00

BRG 304

Luer Lock / Quick Release BRG 304 $40.00

BRG 305

Luer Lock / Quick Release for older TJA / Thermo ICP BRG 305 $40.00

BRG 306

Quick Release for Agilent ICP, Bruker, Finnigan, GBC, Leeman, Varian. BRG 306 $40.00

BRG 308

Quick Release for PE Optima 2000 and 4000 series. BRG 308 $40.00

BRG 309

Quick Release for Spectro. BRG 309 $40.00


4mm Festo/Pisco Pneumatic Quick Release
Description Catalog # US$ Price

BRG 404


Quick Release for 4 mm gas line.
Same style as on many glass nebulizers such as GE EzyLok.
Replaces MM 1020 gas line & BRG 204.
4 mm gas line not included. 		BRG 404 $50.00


2 mm Gas Line
Description Catalog # US$ Price

MM 1020

2 mm gas line with UpChurch fingertight fittings for Mira Mist and Ari Mist nebulizers. MM 1020 $40.00

BRC 20

Black PEEK UpChurch fingertight fitting for 2mm OD gas or sample lines. Used as the standard fitting for our MM 1020 gas lines. BRC 20 $ 15.00




Alternative Adapters for Gas or Sample Lines - Standard IDEX / UpChurch Parts. (Can also be obtained from IDEX at www.idex-hs.com)
Description Catalog # US$ Price

F-120

PEEK Natural UpChurch fingertight fitting for 1/16" (0.0625") OD sample lines. F-120 $ 15.00

P-728-01

Black PEEK UpChurch T fingertight fitting for Mira Mist CE. P-728-01 $40.00

P-200N

Natural Tefzel Ferrule for 1/16” tubing. Fits in P 215 and P 230 UpChurch 1/4 28 fittings. P-200N $ 5.00

P-215

Natural Tefzel 1/4 28 Nut for 1/16” tubing. Requires ferrule such as P 200N. P-215 $ 5.00

P-230

Natural (brown) PEEK 1/4 28 Nut for 1/16” tubing. Requires ferrule such as P 200N. P-230 $ 5.00

P-230BLK

Black PEEK 1/4 28 Nut for 1/16” tubing. Requires ferrule such as P 200N. P-230BLK $ 5.00

P-307

M6 Upchurch fitting for 2 mm gas or sample lines. Fits in P650 UpChurch adapter. Needs a P342 ferrule. P-307 $ 5.00

P-308

1/4 28 Upchurch fitting for 1/8" gas or sample lines. Fits in P652 UpChurch adapter. Needs a P300 ferrule. P-308 $ 5.00

P-300

Ferrule for P308 Upchurch fitting for 1/8" gas or sample lines. P-300 $ 5.00

P-342

Ferrule for P307 Upchurch fitting for 2mm gas or sample lines. P-342 $ 5.00

P-650

M6 Upchurch Adapter for 1/8", 2mm and 1/16" gas or sample lines. Fits in place of the MM 1020 gas line or in place of the sample line. If bought from UpChurch directly, the small bit protruding at the tip must be cut off. Allows M6 fittings to be used to attach gas and sample lines directly to the nebulizer. P-650 $ 20.00

P-652

1/4 28 Upchurch Adapter for 1/8" and 1/16" gas or sample lines. Fits in place of the MM 1020 gas line or in place of the sample line. If bought from UpChurch directly, the small bit protruding at the tip must be cut off. Allows 1/4 28 fittings to be used to attach gas and sample lines directly to the nebulizer. P-652 $ 20.00

P-652-Kel-F

Kel-F 1/4 - 28 Upchurch Adapter for 1/16" sample lines for Agilent Instruments. Allows 1/4 28 fittings to be used to attach gas and sample lines directly to the nebulizer. P-652-Kel-F $ 40.00

.
For prices in £ and €, Click Here
Top  Nebulizers Gas Lines
& Fittings 		Sample Lines
& Fittings 		Discontinued
Nebulizers etc.

Sample Lines & Fittings

Mira Mist and Ari Mist Gas & Sample Line Fittings



Sample Line Fittings
Description Catalog # US$ Price

BRC 3

Blue UpChurch fingertight fitting for 0.044" OD sample lines. These are press fit, and require stretching the sample line to pull through. BRC 3 $ 10.00

BRC 4

Black UpChurch fingertight fitting for 0.044" OD sample lines. These are press fit, and require stretching the sample line to pull through. BRC 4 $ 12.00

BRC 5

KelF Natural UpChurch fingertight fitting for 0.062" OD sample lines. These are press fit, and require stretching the sample line to pull through. BRC 5 $ 12.00

BRC 6

PEEK Natural UpChurch fingertight fitting (UpChurch part # F120) for 0.0625" OD sample lines. These are wider than 0.0625”, and require tightening to hold the sample line. BRC 6 $ 12.00

BRC 9

Red UpChurch fingertight fitting for 0.0625" OD sample lines. Used with our BRC 209 tubing. These are press fit, and require stretching the sample line to pull through. BRC 1 $ 12.00

BRC 20

Black PEEK UpChurch fingertight fitting for 2mm OD gas or sample lines. Used as the standard fitting for our MM 1020 gas lines. These are press fit, and require stretching the gas line to pull through. BRC 20 $ 15.00

BRC 640

Adapter for ESI FAST system mixing T.
For 0.0625" OD sample lines such as BRC 204.
1/4-28 to 10/32 fingertight adapter fitting with BRC 6
(Idex part # P640) 		$ 75.00
Sample Line
Description Catalog # US$ Price

BRC 103

3 meters of .044" OD X .020" ID Clear FEP or PTFE Tubing for sample lines. BRC 103 $ 50.00

BRC 104

3 meters of 1/16" (.0625") OD X .020" ID FEP or PTFE Tubing for sample lines. BRC 104 $ 50.00

BRC 105

3 meters of 2mm OD X 1mm ID FEP or PTFE Tubing for gas lines. BRC 105 $ 50.00

BRC 108

3 meters of .062" OD X .030" ID FEP Extra Wide ID Tubing for T2100 sample lines. Causes pulsing of sample flow unless running 1 ml/min or more. BRC 108 $ 50.00

BRC 109

3 meters of .062" OD X .010" ID PFA Tubing for X-175 & NX-175 sample lines. BRC 109 $ 80.00

BRC 113

30 meters of .044" OD X .020" ID Clear FEP or PTFE Tubing for sample lines. BRC 113 $ 260.00

BRC 114

30 meters of 1/16" (.0625") OD X .020" ID Teflon Tubing for sample lines. BRC 114 $ 260.00

BRC 115

30 meters of 2mm OD X 1mm ID Teflon Tubing for gas lines BRC 115 $ 275.00

BRC 118

30 meters of .062" OD X .030" ID Clear FEP or PTFE Tubing for T2100 sample lines. BRC 118 $ 260.00

BRC 119

30 meters of .062" OD X .010" ID Clear PFA Tubing for X-175 & NX-175 sample lines. BRC 119 $ 380.00
Sample Line Fittings & Sample Line
Description Catalog # US$ Price

BRC 203

0.5 meters of .044" OD X .020" ID
Clear FEP Tubing with attached BRC 3 fitting for sample lines. 		BRC 203 $ 24.00

BRC 203X

10 Pack of BRC 203:
0.5 meters of .044" OD X .020" ID
Clear FEP Tubing with attached BRC 3 fitting for sample lines. 		BRC 203X $ 140.00

BRC 204

0.5 meters of .062" OD X .020" ID
Clear Teflon Tubing with attached BRC 5 fitting for sample lines. 		BRC 204 $ 24.00

BRC 204A

12.5 cm of .062" OD X .020" ID
Clear Teflon Tubing with attached BRC 5 fitting for the nebulizer and Ό 28 fitting for the instrument’s valves. 		BRC 204A $ 50.00

BRC 204X

10 Pack of BRC 204:
0.5 meters of .062" OD X .020" ID
Clear Teflon Tubing with attached BRC 5 fitting for sample lines. 		BRC 204X $ 140.00

BRC 208

0.5 meters of .062" OD X .030" ID
Clear FEP Tubing with attached BRC 5 fitting for T2100 sample lines. 		BRC 208 $ 25.00

BRC 208X

10 Pack of BRC 208:
0.5 meters of .062" OD X .030" ID
Clear FEP Tubing with attached BRC 5 fitting for T2100 sample lines. 		BRC 208X $ 145.00

BRC 209

0.5 meters of .062" OD X .010" ID
PFA Tubing with attached BRC 9 fitting for NX-175 & X-175 sample lines. 		BRC 209 $40.00

BRC 209X

10 Pack of BRC 209:
0.5 meters of .062" OD X .010" ID
PFA Tubing with attached BRC 9 fitting for NX-175 & X-175 sample lines. 		BRC 209X $ 240.00

BRC 2000

0.5 meters of .062" OD X .020" ID PTFE or PFA with attached UpChurch 1/4-28 Kel-F fitting for 1/16" sample lines and P652-Kel-F adapter. BRC 2000 $ 55.00

BRC 2000X

10 pack of 0.5 meters of .062" OD X .020" ID PTFE with attached UpChurch 1/4-28 Kel-F fitting for 1/16" sample lines and P652-Kel-F adapter. BRC 2000X $ 290.00




T2002, Trace and Legere Fittings

T2002, Trace and Legere Fittings

. The T2002, Trace and Legere Nebulizers have Swagelok or barb attachments for the gas lines, and all use the same capillary tubing for the sample lines (0.42" - 0.45" OD). The T2002 ships with 1/4" Swageloks. 1/8” and 4 mm are available if required. Surge Suppressors are available for the T2002 Nebulizers. They are rarely useful for most systems, but are useful for some pumps and chambers.
T2002, Trace and Legere Fittings
Description Catalog # US$ Price

BRC 103

3 meters of .044" OD X .020" ID Clear FEP Tubing for sample lines. BRC 103 $ 50.00

BRC 113

30 meters of .044" OD X .020" ID Clear FEP Tubing for sample lines. BRC 113 $ 260.00

BRC S1

Surge Suppressor for reducing variations in sample flow due to the peristaltic pump. BRC S1 $ 15.00

BRC S1X

10 pack of Surge Suppressor for reducing variations in sample flow due to the peristaltic pump. BRC S1X $ 90.00

.
Top  Nebulizers Gas Lines
& Fittings 		Sample Lines
& Fittings 		Discontinued
Nebulizers etc.

Discontinued Nebulizers & Chambers

Discontinued Nebulizers and Chambers


. The following Nebulizers have been discontinued due to our other nebulizers being so much better. They are no longer available. They are listed for historical record only.

Graphite Mira Mist HS

Same as Teflon Mira Mist, but flat nose and 25% graphite body reduces drops forming at the tip and being re-introduced into the aerosol. Drops being re-introduced are chamber specific, and few chambers have the problem. For those with a drip problem, the GMM HS helps. Not recommended for GE Cyclonic chambers as they do not have the problem. Works for all liquids, as with 100% Teflon.

DescriptionCatalog #US$ Price
Graphite Mira Mist HS GMM-HS 4500 Not Available

Ari Mist HP

The Ari Mist HP is replaced by the SC-175 which runs lower flows and is more stable at low flows. It was designed to run very low sample flows, but needed higher pressure than most systems could provide at 80 psi. Operated from 5 to 1000 ul/min.

Description ID (Microns) Catalog # US$ Price
Ari Mist HP 150 AM HP 5500 Not Available

Burgener Trace


High salts, high solids, virtually unpluggable, Teflon Nebulizer. Once was exclusively available from Thermo Elemental. Has been replaced with the T2100 which is a longer lasting nebulizer with virtually identical operating sensitivity and stability. Optimized for the TJA Trace ICP, TJA Iris, and Cyclonic Chambers. The Trace was discontinued as of January 2008.

Description Catalog # US$ Price
Burgener Trace BTN Not Available

Burgener Legere

High pressure (120 psi), medium sample flow, V Groove design. Fits 0.94" ID chambers. Uses TADP -2 adapter for Scott type chambers. Ideal for low sample flow, high particulate solutions.

DescriptionCatalog #US$ Price
Burgener Legere LTF Not Available

BTS 50

General nebulizer for chambers requiring adapters, such as Scott Double Pass chambers. Shorter nose than T2002, otherwise the same as a T2002. Does not fit most cyclonics.

DescriptionCatalog #US$ Price
BTS 50 BTS 50 Not Available

Burgener OSN 100

Brass Nozzle. Easily removed for quick replacement. No adjustable parts - it just works well all the time. Standard shop pressure (35 - 120 psi), High sample flow, Parallel Path design, large droplet size, does not include gas and liquid attachments which are necessary but designed for each situation and priced accoordingly.

DescriptionCatalog #US$ Price
OSN 100 OSN 100 Not Available

Burgener Flex 50

Stainless Steel and Nylon Nebulizer. Low Pressure (35 - 45 psi), High sample flow, Enhanced Parallel Path design. Designed for Industrial Sprays. Flexible Nebulizer. Bend it to any shape!

DescriptionCatalog #US$ Price
Flex 50 Flex 50 Not Available




Mini Chambers

Mini Chambers are discontinued as of 2018
We have discontinued making mini chambers. The concept of immediate washout is desirable, but actually not related to the size of the chamber. If you spray a mist into a mini chamber at flow rates low enough to allow 100% vaporization before the mist leaves the chamber or before it reaches the torch, then you will get washouts of a few seconds instead of minutes to hours. The time for washout depends on the wetness inside the chamber - wet walls take a very long time to clear of any high concentrations of elements. Several companies and individuals have tried to produce systems with tiny chambers or no chamber. Direct Injection Nebulizers do this - the tip of the nebulizer is at the base of the plasma. This provides instantaneous results with no carry over from previous samples. But it also provides enough large droplets that do not vaporize while passing through the plasma that the plasma is severely affected by the large droplets. You get cold spots in the plasma, and you are seeing spectra from elements mixed with signals from molecules and chemistry happening as the droplets vaporize in the plasma producing oxides and other compounds that effect the spectra. You end up with a poor analysis.

Mini chambers close to the torch have the same problems. The larger droplets do not have time to vaporize, so they interfere with the spectra produced and with the plasma stability. To ensure 100% vaporization, several suppliers of mini chambers directly attached to the torch have determined that they need to heat the chamber. While this will vaporize the droplets, the droplets still hit the walls of the chamber, stick, and vaporize on the wall leaving the valuable elements and molecules you are analyzing on the wall as the water vapor goes to the torch. This ruins your analysis and causes a slow washout, negating any benefit of the mini chamber. We noticed the problem long ago and solved it by adding a 1/2 meter length of Teflon lined tubing between the mini chamber and the torch base. The extra 1/2 meter allowed enough time for the droplets to vaporize and had a tiny effect on the transport rate to the torch. But effectively, we made our 9 ml spray chambers into a 30 ml chamber.

Scott double pass chambers and single pass chambers allow the mist to travel for a while before it hits a wall, so that the droplets have time to vaporize or at least shrink to a small enough size that they do not impact and stick to the wall. Once they are vaporized, then the rest of the travel time is minimal regardless of the size of the chamber.

We ran many tests on chambers and low flows to see what allowed 100% transport to the torch. Preventing the mist from wetting the insides of the chamber was the critical factor. The chamber design was not significant if it could be kept dry. So a Scott Double Pass chamber of 60 ml inside volume gave almost identical results to our 9 ml mini chambers, as long as it stayed dry. It was impossible to keep droplets from hitting the sides of cyclonic chambers at the entry into the cyclone. So cyclonic chambers, chambers with glass beads, and anything with a barrier close to the nebulizer can not provide 100% transport of the sample.

Heating chambers will vaporize all of the droplets, but leave a lot of sample on the chamber walls, so heated chambers only work if the droplets never hit the walls of the chamber which requires a long and large enough chamber to provide time for the droplets to vaporize.

For the mist to travel through a chamber and 100% vaporize, you need a long straight passage, and flow rates well below the saturation rate of the Argon carrying the mist. 1 L/min Argon will vaporize 40 ΅l/min of water. So you need about 20 ΅l/min or LESS sample flow into the chamber to allow the Argon to vaporize it, and you need time to vaporize it.

The Scott chambers have a long straight center tube, followed by a second long passage to the torch connector. This provides a passage length long enough to vaporize the droplets, and has no barriers to catch the mist as it leaves the nebulizer. More ideal would be a long straight tube about 50 cm length leading to the torch base. This will not easily fit most instruments and is not likely to ever be used. So a curved back tube is the next best option, and the Scott is essentially that with a bit of turbulence around the exit point.

For most low flow applications, including single cell analysis, CE interfacing, HPLC interfacing, glass Scott Double Pass spray chambers work better than anything else.

An additional note: If you add some alcohol and run 10% - 100% alcohol instead of pure water, then the droplets will vaporize much faster and your delivery to the torch will be more consistent. Also the droplets will be smaller to start with as the nebulizer is able to break the lower surface tension liquids into much smaller droplets. You still need low flows in the same range. For single cell analysis, be sure that your carrying liquid has something to act as an internal standard. If you have pure water or alcohol, then you have no signal unless a cell passes through. If you have some Yttrium in the solution, you can monitor the Y values as a measure that the system is operating properly.

Discontinued Spray Chambers


Mini Teflon® Chamber
Description Catalog # US$ Price

MC CE

Mini Teflon®Chamber. For Mira Mist CE, Ari Mist, at micro flows only (<20 ΅l/min). Immediate washout - similar to direct injection but much easier to install and use. A glass version is available as part number MGC CE2. MC CE Not Available
Mini Glass Chambers
Description Catalog # US$ Price

MGC CE2

Mini Glass Chamber. For Mira Mist CE, Ari Mist, at micro flows only (<20 ΅l/min). Immediate washout - similar to direct injection but much easier to install and use. The glass version is about 9 ml in volume, and uses a hose with a ball joint fitting to connect to the torch. MGC CE2 Not Available


Large Chambers
Description Catalog # US$ Price


TSDP 01

Teflon® Scott Double Pass Chamber. Standard Scott type chamber, 100% Teflon, no "O" rings. The nebulizer adapter is available as a press fit version with no "O" rings or with "O" rings for glass nebulizers. Works with standard 35 mm adapters and cross flow nebulizers. The Drain is available at various angles. Discontinued. We strongly recommend standard chambers from Glass Expansion and Precision Glassblowing instead of our specialty ones. Our main expertize is Nebulizers. TSDP 01 Not Available

TCA 03

Teflon® Burgener Flip Over Chamber. Similar to standard Scott type chamber, but with flip-over interior producing faster washout. 100% Teflon, no "O" rings. The nebulizer adapter is available as a press fit version with no "O" rings or with "O" rings for glass nebulizers. The Drain is available at various angles. TCA 03 Not Available

TCR 97

Smaller Teflon® Chamber. Good washout. Designed for Scott Double Pass replacement. Fits most systems. Same exterior size as Scott Double Pass. No Adapter required. TCR 97 Not Available

TCR 97C

Same as TCR-97 without insert. Medium washout. Same exterior size as Scott Double Pass. Adapter TABG-1 included. Works with standard 35 mm adapters and cross flow nebulizers. TCR 97C Not Available




. Teflon® is a registered trademark of Chemours Company. In this web page, it refers to PTFE (PolyTetraFluoroEthylene) and/or PFA (Perfluoroalkoxy alkane) and/or FEP (Fluorinated ethylene propylene).